The DeepSoak Pro · Quick start

Ready in 5 minutes.

Watch once, then follow the four steps underneath.

Setup videoComing soon. The four steps below are all you need.
Set it up

Four steps, then get in.

  1. Lay the spa flat in your dry, empty tub. Press every suction cup down firmly.Textured or non-slip tub? Fit the pads first. Show me how
  2. Connect the hose: one end to the control unit, the other to the spa.Push each end in firmly.
  3. Got the lights? Put them in the tub.
  4. Run your bath warm (38–40°C / 100–104°F). Plug in, press the bubble button, get in.

ONE RULE: the control unit always stays outside the bath, on a dry floor.

Quick fixes

Not quite right? Sorted in a minute.

These are the things people ask us most. Each one has a simple fix.

It won't stick, or it lifts up in the water

The suction cups grip a smooth, flat tub floor. They need to go on before the water does.

  1. Empty the tub and wipe the floor.
  2. Dampen each suction cup with a little warm water.
  3. Press every cup down firmly, all 14 of them.
  4. Now run your bath.
Textured or non-slip tub floor?

Suction cups can't seal on a bumpy floor, so use the adhesive pads from your box.

  1. Lay the spa in the dry, empty tub.
  2. Stick one pad on the tub floor under each suction cup.
  3. Press each cup firmly onto its pad until it grips.

It sounds louder than I expected

This is normal

The soft hum is the control unit making your bubbles. Three small things make it quieter:

  • Stand the control unit on a folded towel on the floor.
  • Keep the hose straight, with no kinks.
  • Close the bathroom door.

No bubbles, or they feel weak

  1. Push the hose in firmly at both ends.
  2. Straighten the hose so nothing is bent or trapped.
  3. Plug straight into a wall socket, not an extension lead.
  4. Press the bubble button, then go up a level. There are 6.

Want it warmer? Turn on the warm air with the remote.

Will it fit my tub?

It lies flat on the floor of a standard bathtub. The hose is 1.5 m (59 in), so the control unit sits on the floor beside the bath.

Where are the lights?

The lights are a separate item and are not built into the spa. If you have them, just put them in the tub.

Ordered lights or aroma and can't find them? Email us with your order number and we'll sort it.

Is it safe with water?

Yes

Only air travels down the hose into your bath. The control unit, the plug and all the electrics stay outside the bath on a dry floor.

  • Dry hands when you plug in or unplug.
  • Plug straight into a wall socket.
  • Unplug when you're finished.

After your soak (2 minutes)

  1. Lift the spa out of the tub.
  2. Run the bubbles for a minute to blow out any water.
  3. Unplug, then pull the hose off the spa.
  4. Let the spa dry fully before you put it away.

To clean it, rinse with warm water. No harsh or scratchy cleaners.

Your first 3 nights

Make it a ritual.

Night 1

Just get in.Bubbles on low, 15 minutes. Lie back and let it do everything.

Night 2

Turn it up.Try the higher levels and the warm air. Find your favourite.

Night 3

Make it yours.Same time. Door locked. Phone outside. 20 minutes. Welcome to the 9pm club.

You're one of us now

We've got you.

Talk to us first, about anything at all.

A question, a wobble, a “is this meant to happen?” Email us and a real person from our team will reach out to you personally. Fixed, replaced or refunded: whatever makes you smile again.

team@thedeepsoak.com

Pop your order number in the subject line and we'll jump straight on it.

365 nights. Love it, or every dollar back.
Your card statement will show THEDEEPSOAK.